Showing results: 706 - 720 of 916 items found.
-
Pickering Interfaces Ltd.
Our 8-Pin D-Type connector is used on PXI and LXI switching products to provide a low density user connector solution. A 4-pin partially populated version of the 8-pin D-Type connector is also provided to match the connector pin assignment of our model 40-170 High Power Relay Module.
-
Pickering Interfaces Ltd.
These high-power PXI switch matrix modules provide higher current and power ratings than the high-density switch versions. These modules are designed for the switching of AC or DC loads or for controlling large relay or solenoid systems. The solid state relay matrices occupy two PXI slots and are suitable for automotive and aerospace test applications.
-
RelaySimTest -
OMICRON electronics
RelaySimTest is a software solution for system-based protection testing with OMICRON test equipment that takes a novel, future-oriented approach: the test is independent of relay type and relay manufacturer and the often very extensive parameter settings. Instead, it completely focuses on the correct behavior of the protection system. This is made possible by simulating realistic events in the power system.
-
DARE Electronics
Continuously monitor single or three-phase power lines for over or under voltage conditions with DARE?s AC voltage sensors, voltage monitors, and voltage sensing relays. DARE?s complete line of AC Voltage Sensors will protect system equipment and circuitry from voltage that is hazardous or unsuitable for operation.
-
YAV91074 -
6TL Engineering
The YAV90074 module contents 48 SPDT Relays independent. Each relays PCB contact track is shielded individually in order to handle very low voltage signals and audio signals with extremely low crosstalk. The build-in power supply includes two extra filters to reduce the DC voltage ripple to the relay coils; the control tracks have been drawn in quadrature with signal ones, reducing the inductive coupling produced by the transient current.
-
CXM/128-MF -
Cytec Corp.
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
CPM-10 -
Chuan Sheng Electronics Co., Ltd.
CPM-10 Multifunction Power meter measure single phase 2 wire ,single phase 3 wire, three phase 3 Wire and 3 Phase 4 wire systems with high accuracy measurement for parameters such as voltage, current ,active power, reactive power, apparent power, power factor ,frequency, effective energy (V,A,W,Watt-Hr,Var,Var-Hr,VA,PF,Hz), having LED display and standard communication RTU Modbus RS485..Optional functions 1 set relay output,1 analogue,1 RS485 (ModbusRTU Mode) or 1 pulse output. Most suitable for power management,remote input /output, alarm and remote signal control uses needs.Case depth 120mm only, easy panel mounting installation
-
YAVAR438 -
6TL Engineering
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
Pickering Interfaces Ltd.
Pickering's PXI medium power general purpose switch modules offer higher current ratings in a single 3U slot. The relay solutions have been carefully chosen to ensure a long service life. All the connectors used are fully supported by our cable and connector accessories to simplify system integration.
-
PTE-100-V -
EUROSMC, S.A.
The unit is extremely compact and rugged. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability. This technology allows users to test many different specific functions required in relay testing, without the need of additional accessories.
-
Acces I/O Products, Inc.
Relay is the name for a switch that is operated electro-mechanically or electronically. Their main task is to make and break connections to control the flow of current in electrical circuits. They’re used for various purposes ranging from validating semiconductors to interfacing low power computers or microcontrollers with high power machinery.
-
40-581-002 -
Pickering Interfaces Ltd.
The Worlds highest density 2-pole single slot 3U PXI Matrix Module, the 40-581has 264 crosspoints configured as a 2-pole 33x8 matrix. The use of high density electromechanical relays means that the 40-581 is a low cost high density matrix solution with current handling up to 1 Amp. The 40-581 module is suitable for matrix applications where two signals are required to be switched simultaneously, for example send and return signals in a telecoms system. It is also suitable for applications where reed relay based matrices do not have sufficient power handling capability.
-
-
YAV90087 -
6TL Engineering
8 power relays Switching 20A 250Vac PNP Outputs para control or YAV90304 control CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
PP3CSGRN -
Matco Tools
*Power Probe 3 is a digital multimeter that provides diagnostic power with the flip of a switch*Determine if motors, lights, fans, relays and circuits are operational on and off the vehicle by applying battery power or ground through the tool*Easy-to-read dual polarity indicators feature a red (+) symbol to indicate positive voltage and a green (-) symbol to indicate ground